HOW WE WORK
From first conversation
to reliable partner.
Every bespoke project follows the same proven process. Here’s what to expect when you work with us.
No two projects are the same, but our approach is consistent.
Whether you’re powering a single remote sensor or designing a multi-site infrastructure programme, we follow the same four stages to get you from challenge to working system. At every point, you’ll know what’s happening, what we need from you, and what comes next.
STEP 01: ASSESS
Understanding
your requirements.
Every project starts with a conversation. We want to understand what you’re trying to power, where it is, how much energy it needs, and how critical reliability is to your operation. There are no silly questions at this stage — some of our best projects have started with “I’ve got a problem and I’m not sure where to begin.”
Once we understand your requirements, we look at the renewable energy resource available at your site. We tap into meteorological data providers to assess the wind and solar potential in your specific geographic area, so the system we design is based on real conditions — not assumptions.
We then calculate the minimum power your system will need to generate in order to meet your requirements, and build in a safety factor so you’re covered through the lowest-yield months of the year. The goal is a system that delivers reliable power year-round, not just on the best days.
-
What equipment or load you need to power
-
The location (even a rough postcode or coordinates helps)
-
How long the system needs to run — temporary or permanent
-
Any site constraints (access, planning, environmental)
-
Your budget range, if you have one in mind
-
-
An initial assessment of feasibility
-
Wind and solar resource analysis for your location
-
A clear picture of what’s possible and what it might involve
-
STEP 02: DESIGN
Engineering
the right solution.
With a clear understanding of your requirements and the energy resource available, we design a system tailored to your project. This isn’t a case of picking a product off the shelf — every system is configured around your specific load, location and operating conditions.
Our engineering team selects the right combination of wind, solar and battery storage, sizes every component to handle your peak and average loads, and designs the physical layout to suit your site. If you need remote monitoring, we integrate that from the start. If the project demands it, we partner with experts in other fields — structural engineers, civils contractors, connectivity specialists — to make sure every aspect is covered.
You’ll receive a detailed technical specification and proposal that sets out exactly what we’re recommending, why, and what it will cost. No surprises later.
-
System configuration: wind, solar, battery and ancillary equipment
-
Component sizing based on your load profile and worst-case conditions
-
Site layout and mounting design
-
Remote monitoring specification (if required)
-
Partner coordination for specialist requirements
-
-
A detailed technical specification
-
System schematic and site layout
-
A clear, transparent quotation
-
A timeline for build and delivery
-
STEP 03: BUILD & INSTALL
Manufactured in-house
installed on-site.
Once the design is signed off, our workshop team builds your system. Every component is manufactured and assembled in our Herefordshire facility — from turbine assemblies and solar frames to wiring looms and enclosures. Because we make everything in-house, we control the quality at every stage and can adapt quickly if anything changes during the build.
When the system is ready, we deliver and install it on site. Our team handles the full installation, including turbine and panel erection, electrical connections, battery commissioning and system testing. We don’t leave until everything is running and we’ve confirmed performance against the specification.
For remote or hard-to-reach sites, we’ll work with you on logistics — we’ve shipped systems to over 65 countries and deployed in environments ranging from Antarctic research stations to construction sites and nature reserves. If we can get there, we can power it.
-
In-house manufacturing of all components
-
Quality control and pre-delivery testing
-
Delivery logistics planning (including remote/international sites)
-
Full on-site installation by our team
-
System commissioning and performance verification
-
Handover and on-site training for your team
-
-
A fully installed, tested and operational system
-
Commissioning report confirming performance
-
On-site training for your team (if required)
-
All documentation, datasheets and warranty information
-
STEP 04: MONITOR
Visibility & support
for the long term.
Installation isn’t the end of the project — it’s the beginning. Our custom-built remote monitoring system gives you live visibility of how your system is performing, from anywhere in the world. You can see power generation, battery state, consumption and system health in real time, with full historical data for trend analysis and reporting.
Integrating seamlessly with Victron Energy technology, our monitoring platform lets you track wind and solar inputs, identify issues before they escalate, and adjust settings remotely without a site visit. For us, it means we can keep an eye on your system’s health and proactively flag anything that needs attention.
And because we built the system, we’re the right people to support it. Whether you need a replacement part, a capacity upgrade, or help troubleshooting an issue at 2am in a different timezone, you’re dealing with the engineers who designed and assembled your system — not a call centre.
-
Custom-built remote monitoring hardware and dashboard
-
Victron VRM integration for full system visibility
-
Real-time alerts and remote diagnostics
-
Remote configuration — adjust settings without a site visit
-
Ongoing technical support from our engineering team
-
System repair, upgrade and expansion services
-
-
A monitoring dashboard you can access from any device
-
Ongoing visibility of system performance and health
-
A team that knows your system inside out, available when you need them
-
WHY LEADING EDGE
The difference is inthe detail.
We manufacture everything
Every turbine, every panel frame, every enclosure is designed and built by our team in Herefordshire. That means we understand every component — and we can fix, replace or upgrade any part of your system, years after installation.
We’re a small team, but we’re bigger than we look. When a project needs structural engineering, civils, connectivity or other specialist input, we bring in trusted partners who share our standards. You still deal with us.
We partner when the project demands it
We’re here
for the long term
Our relationship with you doesn’t end at installation. Remote monitoring, ongoing support, repairs and upgrades are all part of what we do. We’ve had systems running continuously in some of the harshest environments on Earth for over a decade.
SEE THE PROCESS IN ACTION
From brief to build:
Elmley Nature Reserve
Elmley Nature Reserve needed to replace their diesel generators with a reliable, clean power solution.
We assessed the solar resource on site, designed a ground-mount solar and battery system sized for year-round operation, built and installed it, and now monitor it remotely to ensure it keeps performing. The result: a nature reserve powered entirely by renewables.